Robustness and efficiency

COINr was the first CRAN package that I built (everyone say “aww”). In the process, I learned a lot about package development, as well as principles about programming in general. However, since I learned this while building the package, especially the first parts of the package that I wrote were (in retrospect) not written very well. For example, although I defined a “COIN” class, I didn’t define methods for the COIN. Much of the code was not written in a “functional” way, and there were not enough checks on the inputs and outputs of the code. All this meant that the code was not very robust and had to be patched, a lot. This made it hard to maintain, less robust, and also slower for the user. As a consequence, I decided to re-write most functions, many from scratch, with a higher standard of programming. I also slimmed down the “COIN” class to a more streamlined “coin” class.

Focus

COINr is a package meant to focus on developing composite indicators. But the focus got lost at some point when I got carried away with html plotly plots and shiny apps. These things, although nice, were in retrospect not really that useful in the package and are also difficult to maintain and bloat out the package. I decided to cut out all interactive plots and apps, but these can still be accessed through the COINr6 package and the conversion functions between COINr and COINr6 (see below).

Dependencies

As a result of the first two points (inexperience plus straying off track), COINr had many dependencies, i.e. packages that had to be installed to install COINr. Although there is no harm in loading 10 or 20 packages when performing data analysis in R, this can become a problem if you are building a package because every user has to have these packages installed. If you have ever had to install several packages at the same time in R, you have probably run into some kind of problem. Moreover, COINr is dependent on any changes in those packages, and that makes maintaining it more difficult. This meant that in practice, COINr was not always easy to install. I decided to re-write the package almost entirely in base R, to remove as many dependencies as possible.

Features and flexibility

One thing that was missing from COINr was proper support for panel data (time-dependent data). This has now been mostly rectified with the introduction of the “purse” class. The main “building” functions of COINr have also been re-written as generics, with methods for coins, data frames and purses. Moreover many functions allow you to call other functions, which makes COINr much easier to link up with other packages.

Syntax

COINr syntax was inconsistent. While this was not a critical problem, since I was making big changes to the package I decided to take the opportunity to make the syntax as consistent as possible. This is a one-off change and won’t be messed around with any more!

Function names

Many things have changed. The first thing you will probably notice is the syntax. Because I was anyway making syntax-breaking changes to the package, I decided to go all in, and try to make the syntax as consistent as possible. This means that function names are more predictable: all “building” functions start with a capital letter. Plot functions start with plot_. Analysis functions mostly start with get_. Functions are generally in lower case. This all hopefully makes the package a little easier to use. You will notice that calling an old < v1.0 function name will generate an error, which redirects you to the new function name. My hope is that although this is inconvenient, it will not take too long to adapt to the new function names. In most functions, the main logic behind the arguments is pretty similar. As mentioned above, I’m not going to change all the names again; this is a one-off thing.

Function features

The second obvious change is that some of the key functions themselves have changed syntax: they have been re-written to be more flexible and more robust. This may seem annoying but I promise you it is for the greater good. I can’t describe all the changes here, but in general functions have been made more flexible: for example Normalise() now can take any normalising function, rather than a fixed set of options. Outlier treatment also allows to pass outlier detection and treatment functions. The sensitivity analysis function (now get_sensitivity()) now allows to target any part of the coin at all, not just function arguments. In general, the core “building” functions now call other lower-level functions and this makes it easier to hook COINr up to other packages, for example using more sophisticated imputation and aggregation methods.

New “coin” class and methods

The third related change that is perhaps not so obvious is that the structure of the central object in COINr, the “COIN”, has changed. The object has been streamlined and tidied, and has a new S3 class called a “coin” (the difference being that the new coin is lower case). If you have previously built a COIN using an older version of COINr, it will not work in the new version of COINr! But the good news is that there is a handy function called COIN_to_coin() which converts the older “COIN” class to the newer “coin” class.

The new “coin” class also comes with a number of methods. All the main construction functions now have methods for at least coins, data frames and purses (see next sub-section), and some have methods for numerical vectors. This is in contrast to the older COINr versions which did not define formal methods. See the Building coins vignette for more details.

Purses and panel data

The new “purse” class gives a formal way to deal with panel data (time indexed data). A “purse” is a time-indexed collection of coins. All construction functions have purse methods, so working with time data becomes very straightforward.

Purses and purse methods are still being expanded in COINr so keep an eye out for new features if you are interested. See the Building coins vignette for more details.

Documentation

The next thing is that the documentation has been completely re-written, with loads of new vignettes! And even better, COINr now lives at a web-page built with “pkgdown” which you can find here, where all the documentation is easily accessible. So each function is well-documented. Hurray.

Removed functions

The last very obvious change is that some functions have disappeared! Where have they gone? You may notice that all functions that generated interactive plots (often called iPlot* in previous versions of COINr), plus all shiny apps, have vanished. The reason for this, as explained above, is that these tools were distracting from the main point of the package and were too much effort to maintain. Moreover, even though interactive plots are great if you are outputting html documents, for pdf and word they are a hassle because it is quite unpredictable how they will be rendered. The good news is that I have replaced some of the interactive plots with static versions, such as plot_framework(), and plot_scatter(), so you can still do most of the plotting as in the previous versions, but with more predictable (and more usable) outputs.